Actually, I had a related question on VHB 30's. When I rebuilt mine (with MG Cycle's gasket kits), there were no o-rings on the idle mix and idle speed screws, although they are shown on the VHB 30 parts diagram. Does anyone know if they are supposed to be there, or is this a mistake on the diagram, or on the Carbs, or in the kit? Thanks, -tom
On Mon, 7 Feb 2005 07:32:33 -0700 Steve Farris <nmwi-@msn.com> wrote:
Your free subscription is supported by today's sponsor: ------------------------------------------------------------------- Would You Like Your Money 2-Day? Get started now! TaxBrain Online. http://click.topica.com/caac8vpb1dfltbOluDFa/TaxBrain -------------------------------------------------------------------
bob c., what paul said about the kits. the kits have all the o rings and gaskets you need and more. Steve
71 Ambo (about to go under the knife) 72 Eldo (almost ready to roll) ----- Original Message ----- From: Custom Guzzi To: Loopfram-@topica.com Sent: Monday, February 07, 2005 5:58 AM Subject: RE: VHB 29 rebuild
Your free subscription is supported by today's sponsor: ------------------------------------------------------------------- Get a FREE* Portable Satellite Radio - yours to keep! Click Here! http://click.topica.com/caac8uyb1dfltbN3z84a/Portable Satellite Radio Promotion -------------------------------------------------------------------
MG Cycle has the kits.
Paul 73 Eldo "Elvira" 949 conversion 74 Eldo "Daisy" undergoing a full police restoration
-----Original Message----- From: BOB COLLETT [mailto:coll-@rjrt.com] Sent: Monday, February 07, 2005 7:07 AM To: Loopfram-@topica.com Subject: RE: VHB 29 rebuild
Your free subscription is supported by today's sponsor: ------------------------------------------------------------------- Need a Laptop? Get a Sony Vaio Laptop Free! http://click.topica.com/caac8usb1dfltb6GIoLa/ProductTestPanel -------------------------------------------------------------------
Where did you gusy get your VHB carb rebuild kits? Was it a complete, don't need anything else type kit? I've got 2 VHB 30's I need to rebuild and replace the AMALS I'm running. No problems with the AMALS just want to try the Del's.
Thanks Bob STEVE FARRIS wrote:
Messagethanks paul, that's exactly what I've put on so far so I hope I'm
"good to go"
gonna go get some fresh gas and give it a try tonight. steve ----- Original Message ----- From: Custom Guzzi To: Loopfram-@topica.com Sent: Saturday, February 05, 2005 3:42 PM Subject: RE: VHB 29 rebuild
Paul, thanks you are correct I didn't mention the fiber
washer on the fuel
banjo. but that's not the one I'm concerned about. the
fuel inlet washer is
about 10-12mm OD the fiber washer I'm wondering
about is the smallest
one, about 4 or 5mm OD with about a 3mm ID. thanks steve ----- Original Message ----- From: Custom Guzzi To: Loopfram-@topica.com Sent: Saturday, February 05, 2005 12:17 PM Subject: RE: VHB 29 rebuild
Your free subscription is supported by today's sponsor: ------------------------------------------------------------------- We have the 42 Inch Plasma TV you've been looking for!! Sony or Panasonic 42 Inch Plasma Wide Screen TV's. Put one up on your wall today! Click Below http://click.topica.com/caac8uBb1dfltb6GIoLf/ExclusiveRewards -------------------------------------------------------------------
Your free subscription is supported by today's sponsor: ------------------------------------------------------------------- Register today for your chance at our Five Thousand Dollar scholarship. Take advantage! Click Here today. http://click.topica.com/caac8uub1dfltbN3z84f/FreeScholarshipGuide -------------------------------------------------------------------
Your free subscription is supported by today's sponsor: ------------------------------------------------------------------- Need a Laptop? Get a Sony Vaio Laptop Free! http://click.topica.com/caac8usb1dfltbOluDFf/ProductTestPanel -------------------------------------------------------------------