Topica Loopframe_Guzzi Archive
Topica Loopframe_Guzzi Archive
Topica Loopframe_Guzzi Archive
Topica Loopframe_Guzzi Archive
Topica Loopframe_Guzzi Archive
 

Subject: RE: exhaust probs

Author: Zerhackermann

Date: Jul 26, 2002, 12:44 PM

Post ID: 1710677612

In thinking about this I wondered...could it be that the nut *seems*
tight, but isn't really all the way in and the headers are bashing
slightly back and forth, hammering the seal? Perhaps thebottom couple
threads are buggered or carbon clogged? Maybe a dremel with wire brush
could help that?

-----Original Message-----
From: Martin Cooke [mailto:cook-@virgin.net]
Sent: Friday, July 26, 2002 9:44 AM
To: Loopfram-@topica.com
Subject: Re: exhaust probs


i've seen similar on my friends bike. i assume the gasket has flattened,
not the manifold nut come loose. don't see how it can tighten itself up.

cookie


----- Original Message -----
From: "Kevin Graf" <kgr-@midwestpension.com>
To: <Loopfram-@topica.com>
Sent: Friday, July 26, 2002 3:12 PM
Subject: RE: exhaust probs


Well, I think at one point we came to the conclusion that it would
helps seal, reduce vibration through the threads and make up for wore
threads to
a
certain extent, and helps the nut stay put a bit longer.
My locking exhaust nuts still come loose. Even though the lock nut is
tight,
the actual exhaust nut backs it's way out a hair enough for the engine

vibration to waste the gasket. The only real way to tell this is by
loosening the locknut. Then I can clearly see that the exhaust nut
decided to run away again. It's weird, I know, but I have been careful

to notice
if
the exhaust nut comes loose with the lock nut while I'm loosening it
and
it
doesn't. It does it all on it's own. I probably got some real wore
threads.
I would suggest you try loosening the locknut to see where the exhaust

nut is at, if you haven't already...

Kev

-----Original Message-----
From: Martin Cooke [mailto:cook-@virgin.net]
Sent: Friday, July 26, 2002 9:18 AM
To: Loopfram-@topica.com
Subject: Re: exhaust probs


what's the RTV supposed to do?

cookie

ps i got the locking nuts on my own bike & i never have to touch them
or
the
gaskets.


----- Original Message -----
From: "Kevin Graf" <kgr-@midwestpension.com>
To: <Loopfram-@topica.com>
Sent: Friday, July 26, 2002 12:59 PM
Subject: RE: exhaust probs


If you got the frame clamps and the locking nuts(I got 'em too but
I'm
not
quit sure if they were worth the $$)You can try some hi-temp RTV on
the threads (tip from the list!). The combination of these three
things seem
to
make my gaskets last a bit longer.

Kev

-----Original Message-----
From: EldoMike [mailto:msse-@classicguzzi.com]
Sent: Friday, July 26, 2002 7:43 AM
To: Loopfram-@topica.com
Subject: Re: exhaust probs


Has it got the frame to exhaust pipe clamps?

Mike
www.classicguzzi.com

----- Original Message -----
From: "Martin Cooke" <cook-@virgin.net>
To: <Loopfram-@topica.com>
Sent: Friday, July 26, 2002 3:19 AM
Subject: exhaust probs


to whoever wrote this (i've lost track):

"cookie I always thought exhaust if it pops letting off the
throttle
and
intake air leak if it popped getting on the throtle? B."

an air leak at the exhaust manifold will pop on the over run. an
air
leak
on
the intake will just make it run weak in my experience.

now if anyone knows how to stop an eldo getting a loose joint at
the head/downpipe i'd like to know. got a friends bike doing this
all the
time.
NOT the nut coming loose (it's the locknut type), it just eats the
gasket
after a few miles, air gets in, backfires like crazy. i put new
gaskets
in
&
it's fine for a while, then same thing.

it started happening when new mufflers were fitted with rear
balance
pipe
removed. i think it may be to do with the pipes moving &
flattening
off
the
gaskets. however the exhaust assy doesn't appear to be moving any
more
than
stock.

i must have put 6 sets of ex gaskets in that bike & i'm getting
fed up
now.

cookie


----- Original Message -----
From: "E. C. Bud Durdle" <bu-@olympus.net>
To: <Loopfram-@topica.com>
Sent: Friday, July 26, 2002 1:46 AM
Subject: Re: Digest for Loopfram-@topica.com, issue 861


On Wednesday 24 July 2002 10:16 pm, you wrote:
I heard a little while ago that the popping could be from
looseness
at
the
head/exhaust header joint, or somewhere close to that. Check to
make
sure
the exhaust is tight up there, and/or has no leaks.

I am working on a 74 Eldo I just picked up with Amal Carbs.
When I
let
off the throttle and am gearing down
it pops through the mufflers. I have played with the air screws
and it
has
gotten better, but it is still
there. I have checked the carb intake gaskets and they are fine.
Someone
told me
this is a common problem with running amals on a Guzzi. Any ideas



Date: Wed, 24 Jul 2002 09:05:15 +0100
From: "Martin Cooke" <mjco-@nildram.co.uk>
Subject: Re: carb & air filter question


almost certainly an air leak as matt has said

cookie

cookie I always thought exhaust if it pops letting off the
throttle
and
intake air leak if it popped getting on the throtle? B.

Entire thread: