| | From: Paul Linn <paul_-@yahoo.com>
Reply-To: Loopfram-@topica.com
To: Loopfram-@topica.com
Subject: RE: db floorboards
Date: Sun, 29 Jul 2001 18:57:32 -0400
============================================================
Get your FREE credit report @ ConsumerInfo.Com!
http://click.topica.com/caaacMAb1dfltb2tZVva/ConsumerInfo
============================================================
Chris,
Yes it's called Triad Foundry.
Paul
-----Original Message-----
From: Chris Berry [mailto:guzzis-@hotmail.com]
Sent: Sunday, July 29, 2001 6:55 PM
To: Loopfram-@topica.com
Subject: RE: db floorboards
============================================================
Get your free credit report online, by fax or mail.
Always private and always secure, click here to get
yours FOR FREE at ConsumerInfo.Com!
http://click.topica.com/caaacMeb1dfltb2GgTda/ConsumerInfo
============================================================
Paul-
What was the place that did the casting for you? Is it in Greensboro?
Thanks!
Chris in NC
| | From: Paul Linn <paul_-@yahoo.com>
Reply-To: Loopfram-@topica.com
To: Loopfram-@topica.com
Subject: RE: db floorboards
Date: Sun, 29 Jul 2001 17:02:02 -0400
============================================================
Get your free credit report online, by fax or mail.
Always private and always secure, click here to get
yours FOR FREE at ConsumerInfo.Com!
http://click.topica.com/caaacMib1dfltb2tZVva/ConsumerInfo
============================================================
As far as I know, you can't buy a new shifter for these boards. If you |
| | otherwise, please share the location. I did find out that I could just
press
the shaft thru with a press and it made the splines.
Paul
69 Ambo
.5 74 Eldo
-----Original Message-----
From: Gary Cheek [mailto:kg8-@home.com]
Sent: Sunday, July 29, 2001 4:58 PM
To: Loopfram-@topica.com
Subject: RE: db floorboards
============================================================
Visit the Consumer Reports Auto Hub for FREE automotive
information. Get negotiating tips, see our Top Picks
for 2001, read feature articles and more at
http://click.topica.com/caaacEQb1dfltb2GgTda/ConsumerReports
============================================================
The lever he wants to use is made from cast aluminum. Welding steel to
aluminum is a lot harder than about 15 minutes at the Bridgeport:-)
Easier still buy a new one. I think he was trying to save a few bucks.
Martin Cooke wrote:
| | If all you want is a different length of lever, why not take a stock
item &
cut & shut it, fill with braze & re-chrome.
Sounds a lot easier to me.
cookie
----- Original Message -----
From: Gary Cheek <kg8-@home.com>
To: <Loopfram-@topica.com>
Sent: Sunday, July 29, 2001 5:39 PM
Subject: RE: db floorboards
| | ============================================================
Get your free credit report online, by fax or mail.
Always private and always secure, click here to get
yours FOR FREE at ConsumerInfo.Com!
http://click.topica.com/caaacMnb1dfltb2DS92a/ConsumerInfo
============================================================
Just saw this post and figuired a response was in order. I read
another response commenting on the use of a broach. While a broach |
|
|
| | | | | | used in production applications the cost in this case is of course
extreme. The heating method will only find the part you desire to |
|
|
| | | | | | to be quenched quickly when contact is made with the male |
|
|
| | of
| | | | course the male part is preheated. In the case of heating to form ,a
suitable part will be very hard if not impossible . You also stand a
very good chance of destoying your casting.
The way we would most likely undertake cutting the inside spline |
|
| | | | be to use a cutter sharpend to conform with the desired profile. We
would then center the workpiece mouted on a rotary table below the
spindle of a vertical mill IE:"Bridgeport" . The work piece would be
offset to correspond to the major diameter. The cutter would be |
|
|
| | | | | | slotter style thru the bore,retracted ,the rotary table would be |
|
| | | | the appropriate nunber of degrees . The steps repeated till the |
|
|
| | | | | | was formed . This process could well be acheive with other machines |
|
|
| | | | | | adapting the scheme . A lathe with a means to index the spindle |
|
|
| | | | | | work as would a stout drill press or an arbor press.
If you cannot find a local shop with these capabilities let me know |
|
|
| | I
| | | | can probably do the job for you.
Gary Cheek
1971 Ambassador
1972 Eldorado
Previous
1970 Ambassador
1973 Eldorado
1984 Ducati 900 SS
1974 Ducati 750 SS
1972 Ducati 450
...And over 30 Bristish Bikes
BTW Should you happen to come across asuitable broach NEVER |
|
|
| | it
| | | | as was posted earlier. A broach is pused thru ,from one side to the
other dragging it backwards will only dull the cutting edges.
Paul Linn wrote:>
============================================================
| | Need to s-t-r-e-t-c-h your dollars?
Get more bang for your buck with cool savings, hot deals, &
free stuff.
http://click.topica.com/caaacgFb1dfltb2GgTda/TopOffers
============================================================
If this is aluminum do not heat red hot. It will melt first. If |
|
|
|
| | | | | | | | aluminum
drill the hole for the fastener tighten it up just enough to fit |
|
|
|
| | over
| | | | | | the
end of the spline then tighten the bolt a little and tap it with |
|
|
|
| | | | | | | | piece
of wood so as not to mar the outside surface and when its on |
|
|
|
| | find
| | | | | | a
spline. aluminum is soft. IIt won't hurt the spline. If your going |
|
|
| | | | | | heat
treat it do it after the spline is made.
Date: Thu, 12 Jul 2001 00:27:41 EDT
From: GUZZI-@aol.com
Subject: Re: DB Floorboard Shifter
drill the hole close to outside diameter,heat spline red hot and |
|
|
| | | | | | it
in,let cool,done.Dont know if this will work,but its the only |
|
|
|
| | I
| | | | | | can
come up with,Mark.wwwmotoguzziclassics.com
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address athttp://mail.yahoo.com |
============================================================
Sign up for My Topica and get a FREE, personalized web page
for all your subscriptions, online reading and posting
privileges, special offers, and more!
http://click.topica.com/caaabHSb1dfltb2DS92f/register
============================================================ |
|
============================================================
Sign up for My Topica and get a FREE, personalized web page
for all your subscriptions, online reading and posting
privileges, special offers, and more!
http://click.topica.com/caaabHSb1dfltb2GgTdf/register
============================================================
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address athttp://mail.yahoo.com
============================================================
Enjoy your vacation more knowing that My Topica won't
overstuff your inbox! When you come back, your email will,
too. Refreshed. Relaxed. Ready to be read. Sign up for free
email R&R.
http://click.topica.com/caaabHTb1dfltb2tZVvf/register
============================================================ |
_________________________________________________________________
Get your FREE download of MSN Explorer athttp://explorer.msn.com/intl.asp
============================================================
Stretch your dollars.
Make George do double duty with amazing deals from
TopOffers.
http://click.topica.com/caaacgOb1dfltb2GgTdf/TopOffers
============================================================
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address athttp://mail.yahoo.com
============================================================
Enjoy your vacation more knowing that My Topica won't
overstuff your inbox! When you come back, your email will,
too. Refreshed. Relaxed. Ready to be read. Sign up for free
email R&R.
http://click.topica.com/caaabHTb1dfltb2tZVvf/register
============================================================ |