Subject: Re: T 3 front end
Author: Edward Walton
Date: Mar 9, 2005, 11:54 AM
Post ID: 1718517750
Yes your right I have seen eldo`s that look stock and have disk brakes. Whats different between the t3 and t front ends ? I would like to keep the same eldo guage head light etc. Calipers ,rotors, master cyl , wheel ,fender & braces, headlight, guages, I will need all of that and more and it will not even look like an eldo frontend. This is going to be exspensive!
From: thomas halchuk <halc-@comcast.net>
Reply-To: Loopfram-@topica.com
To: Loopfram-@topica.com
Subject: Re: T 3 front end
Date: Wed, 9 Mar 2005 09:54:17 -0500
Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Erase wrinkles without painful injections with Nexiderm SP.
Nexiderm SP is clinically proven to reduce wrinkles by 68% Start
your free 14-day trial today!
http://click.topica.com/caadfBPb1dfltb6PLDGa/Nexiderm
-------------------------------------------------------------------
Ted
I was assuming that you want to keep your Eldo as original as possible when
I made my suggestions. I forgot to mention that if you put on a T3 front
end you will need to use the T3 gauges, find a new location for the
ignition, do some rewiring, install (2) calipers with pads, install brake
lines and install a complete master cylinder.
Good Luck
----- Original Message -----
From: "Ken Pitts" <MGcoo-@aol.com>
To: <Loopfram-@topica.com>
Sent: Wednesday, March 09, 2005 9:16 AM
Subject: Re: T 3 front end
Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Erase wrinkles without Botox! Nexiderm SP is clinically proven to
reduce wrinkles by 68% Start your free trial today and pay only
$5.95 for shipping & handling.
http://click.topica.com/caadfBTb1dfltb7hDhIa/Nexiderm
-------------------------------------------------------------------
In a message dated 3/9/05 1:56:26 AM, tedwa-@hotmail.com writes:
| Can you put the t3 on the eldo and if you can what do need to make it fit !? |
Ted
The T-3 front forks can easily be put on a loopframe. You need the complete
front end with triple clamps, remove the lower head bearing & place a .1000"
spacer under the bearing, it will then bolt right up. The problem area is if
you want to keep the Eldo fender, I believe the fender braces to mount an
Eldo
fender to these forks are very hard to come by. Also keep in mind that that
the
T-3 forks will most likely need new dampers & springs to really make them
work as well as they should.
Ken
Asheville, NC
Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Get both the PlayStation2 and Game Cube for Free! Click here to
find out how.
http://click.topica.com/caadeMkb1dfltb7hDhIf/ConsumerResearch
-------------------------------------------------------------------
Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Sign up today for a No Annual Fee Discover®Platinum Card and get�
0% Intro APR on Purchases & Balance Transfers for 8 Months, Up to
2% Cashback Bonus®reward on your purchases & 100% fraud
protection.
http://click.topica.com/caadfzUb1dfltb6PLDGf/DiscoverCard
-------------------------------------------------------------------
Open your e-mail without having to worry about viruses with MSN Premium: Join now and get the first two months FREE*